Central Kentucky · Roof Code
A second layer of shingles over the old roof is allowed in Kentucky in specific situations — and flatly prohibited in three. The one that ends most conversations: if the roof already has two or more applications of any type of roof covering, a re-cover is not permitted. It has to come off.
“Can you just go over it?” is the second question on almost every roof estimate, usually right after price. The answer is in the reroofing section of the residential code Kentucky has adopted, and it is more specific than either side of that conversation usually expects. The code separates two different jobs — replacement and re-cover — and gives each its own rule.
Can you put a new roof over an old roof in Kentucky?
Sometimes. A re-cover is permitted when the new covering is installed per the manufacturer’s approved instructions, or when the new system is structurally independent of the old one.
Section R908.3.1 of the residential code allows installing a new roof covering over an existing one where any of these conditions occur: the new covering goes on “in accordance with the roof covering manufacturer’s approved instructions”; the new system is a “complete and separate roofing system,” such as a standing-seam metal roof, “designed to transmit the roof loads directly to the building’s structural system” without relying on the old roof for support; metal panel, metal shingle, or concrete and clay tile over existing wood shake, applied per R908.4; or a new protective coating over an existing spray polyurethane foam system.
That first condition is the one that does the work on a shingle job, and it is why the shingle manufacturer’s installation instructions — not a rule of thumb — decide whether a particular re-cover is code-compliant.
Two existing layers is the hard stop. Not a judgement call, not a preference — the code says a re-cover shall not be permitted.
When is a roof-over not allowed at all?
Three conditions. A water-soaked or deteriorated existing roof, an existing covering of slate, clay, cement or asbestos-cement tile, or a roof that already carries two or more applications of any covering.
Section R908.3.1.1 lists them without qualification — a re-cover “shall not be permitted” where:
- “the existing roof or roof covering is water soaked or has deteriorated to the point that the existing roof or roof covering is not adequate as a base for additional roofing”;
- “the existing roof covering is slate, clay, cement or asbestos-cement tile”;
- “the existing roof has two or more applications of any type of roof covering.”
Read the third one carefully: any type. Two layers of shingles counts, and so does a layer of shingles over an old layer of something else. The count is of applications, not of materials. This is also why the first thing worth doing before pricing a roof-over is a corner lift at the eave to count what is actually up there, rather than taking a previous owner’s word for it.
What does the code mean by roof replacement?
Tear-off to the deck. Section R908.3 states that roof replacement “shall include the removal of existing layers of roof coverings down to the roof deck,” with one ice-barrier exception.
The exception is narrow and useful: “Where the existing roof assembly includes an ice barrier membrane that is adhered to the roof deck, the existing ice barrier membrane shall be permitted to remain in place and covered with an additional layer of ice barrier membrane.” An adhered ice barrier is the one thing you are allowed to leave bonded to the deck, because removing it generally damages the sheathing. Central Kentucky roofs are inside the climate zone where an ice barrier is required, so this comes up on most tear-offs here.
Two reroofing rules that save money
Section R908.1 carries two exceptions that keep a reroof from triggering a redesign. Reroofing is not required to meet the minimum design-slope requirement of one-quarter unit vertical in 12 units horizontal for roofs that provide positive drainage; and for roofs with positive drainage, re-covering or replacing a covering “shall not require the secondary (emergency overflow) drains or scuppers of Section R903.4.1 to be added to an existing roof.”
That second exception is worth knowing on a low-slope residential section, because adding overflow drains or scuppers to an existing roof is a structural and plumbing job, not a roofing line item. Note what the exception does not excuse: R908.2 still requires the structural roof components to be “capable of supporting the roof covering system and the material and equipment loads that will be encountered during installation.” A second layer adds dead load, and the exceptions above say nothing about that.
What gets replaced even on a re-cover
Section R908.5 is explicit that existing flashings, edgings, outlets, vents “or similar devices that are a part of the assembly shall be replaced where rusted, damaged or deteriorated,” and that aggregate surfacing materials shall not be reinstalled. R908.6 requires flashings to be reconstructed per the manufacturer’s installation instructions, and metal flashing receiving bituminous material to be primed first.
In the field, that list is where the difference between two bids usually hides. A re-cover quote that leaves old pipe boots and rusted drip edge in place is cheaper for a reason the code already answered. If you are comparing estimates, ask which of those devices is being replaced and which is staying — and whether a permit is being pulled for the work.
One more that catches older houses: R908.4 requires that where a new covering over wood shingle or shake creates a combustible concealed space, “the entire existing surface shall be covered with gypsum board, mineral fiber, glass fiber or other approved materials securely fastened in place.” Going over a wood shake roof is allowed in the metal and tile cases, but not bare.
How do I tell how many layers are on my roof?
The usual method is to lift a shingle at a rake or eave edge where the layers are visible in section, or look at the exposed edge at a gable. Measuring the stack at the drip edge gives a reasonable read too. It has to be established before a re-cover is priced, because R908.3.1.1 prohibits a re-cover where two or more applications already exist.
Is a metal roof over shingles allowed in Kentucky?
A re-cover is permitted where the new covering is installed in accordance with the roof covering manufacturer’s approved instructions, and separately where the new system is a complete and separate roofing system, such as standing-seam metal, designed to transmit roof loads directly to the building’s structural system without relying on the existing roof for support. The prohibitions in R908.3.1.1 still apply — including the two-application limit.
Which code book is this?
The reroofing provisions quoted here are Section R908 of the residential code Kentucky has adopted — the 2018 Kentucky Residential Code, Third Edition, published by the Kentucky Department of Housing, Buildings and Construction and linked above. Local amendments and the inspector of record still govern a specific job, so confirm scope with the office issuing your permit.
Primary source: the 2018 Kentucky Residential Code, Third Edition, Kentucky Department of Housing, Buildings and Construction.
Last updated November 12, 2026.
By Central Roof Repair · Roof repair across Central Kentucky · Call or text (859) 310-1209.

Leave a Reply